Forum Topic

*Globe Tattoo Broadband Wired ADSL/VDSL Thread (Check Page 1 For FAQ's)

  • VDSL2 Plan 1899 20 mbps, since Nov 2018, Imus area

    Up Rate: 36181 kbps
    Down Rate: 120468 kbps
    Upstream Noise Margin: 6.2 dB
    Downstream Noise Margin: 8.8 dB
    InterleaveDepth: 1
    Line Standard: G.993.5_Annex_B


    Boss, paano naging ganyan upload speed mo? Grabe taas ng upload!
    Ang ayoko lang kasi talaga sa Globe, yung sobrang baba ng upload speed.
    Kailangan ko kasi talaga ng mataas na upload speed.
  • ^ nung minigrate kase ganyan na talaga haha. Nagulat na lang ako kase antaas ng upload mataas pa sa downlink speed ko.
  • Hi

    Here's my planned setup of two routers through DMZ. Kindly comment if workable.

    Hardware:-
    1)  Main ISP supplied Modem router:  ZTE ZHXN H108N V2.5 IP address is 192.168.254.254 (ISP supplied modem router)

    2)  Secondary router: TP Link AC2300 IP address is 192.168.0.1 (router).

    ISP broadband connection is through PPPoE.

    Planned set up:

    ISP Modem/Router (ZTE ZHXN H108N) LAN port ---->connect through DZM mode --->2nd router (TP-Link AC2300) WAN port

    ************************************************
    Router 1 (Main ISP supplied Modem router ZTE)

    WAN IP Address: xxx.2xx.xxx1xx (default by ISP)

    LAN Setup
    LAN IP Address:  192.168.254.254 (default by ISP)
    Subnet Mask: 255.255.255.0 (default by ISP)
    DHCP:  ON
    DHCP Range:192.168.254.100 to 192.168.254.200 (default by ISP)

    WIFI: OFF

    NAT: ON (Guessing here.  Not sure if it will cause double NAT issues.  Please comment.)

    UPnP:  ON
    WAN Connection: (what to put?)
    Advertisement Period (in minutes): not sure what is this?
    Advertisement Time to Live (in hoops):  not sure what is this?

    DMZ Setup : ON
    WAN Connection:  (what to put?)
    DMZ Host IP Address: 192.168.0.10 (router 2 IP Address is that correct?)
    MAC : ON

    Port Forwarding:  Have to setup or not?

    -------------------------------------------------------------------------------
    Router 2 (TP-Link AC2300)

    WAN IP Address: 192.168.254.254 (Guessing here to use Router 1 IP address)
    Gateway: 192.168.254.254
    Primary DNS Server: 192.168.254.254

    Static IP on WAN Port: 192.168.0.10 (correct or not?  Does it have to be the same as the LAN IP Address?)

    LAN Setup
    LAN IP Address:  192.168.0.10
    Subnet Mask: 255.255.255.0
    DHCP:  ON
    DHCP Range:192.168.0.100 to 192.168.0.200

    WIFI: ON

    NAT: ON (Guessing here.  Not sure if it will cause double NAT issues.  Please comment.)

    UPnP: ON

    FIREWALL:  IPv4 IPv6: ON

    Internet Connection: through Static IP

    ====================================

    Question:
    1) Do I enable the DHCP on BOTH the main modem/router (ie the ZTE ZHXN H108N) and secondary router (TP Link AC2300)? Will it conflict each other?  What range should I put on both?  Does it have to be very different IP address range?

    2) Will connecting two routers caused double NAT? Will that even be an issue?

    3)  How about Voip? Will it be effected?

    4) How about the UPnP? Do i enable it on both or none?

    5) What internet connection type do I choose on the secondary router TP Link AC2300 since it offered 5 types (Dynamic IP, Static IP, PPPoE, L2TP and PPTP)?

    7) Should I turn off the wireless radio on the ISP modem/router (ZTE)?

    Thanks in advance.

    -- edited by boltvoltes on Apr 27 2019, 07:36 PM
  • ^ Let's correct some:
    Your MODEM(your router 1)
    UPnP: ON
    WAN Connection: (what to put?)
    Advertisement Period (in minutes): not sure what is this?
    Advertisement Time to Live (in hoops): not sure what is this?

    Please DISABLE or OFF UPnP. DMZ is what we are doing here which OPENs all ports to the specific IP.
    then
    DMZ Setup : ON
    WAN Connection: (what to put?)
    DMZ Host IP Address: 192.168.0.10 (router 2 IP Address is that correct?)
    MAC : ON

    your WAN connection. What option is there? AFAIK that's where your DSL port/settings should be. Sorry I am on FiberHome modem so have no idea.
    But your DMZ Host IP: 192.168.254.xxx (eg: 192.168.254.100). Since this is Modem DHCP it only entertains IP within it's subnet.
    Port Forwarding: Have to setup or not?

    Nope not on Globe's modem. Since we already DMZ'd it to your router. Basically ALL ports are open for that specific IP.

    Router 2:
    WAN IP Address: 192.168.254.254 (Guessing here to use Router 1 IP address)
    Gateway: 192.168.254.254
    Primary DNS Server: 192.168.254.254

    WAN IP address: Should be what you set in the DMZ IP. So change this to example 192.168.254.100.
    Gateway correct. DNS server you can change that as you like. I recommend primary: 1.1.1.1 and 1.0.0.1 secondary.
    Static IP on WAN Port: 192.168.0.10 (correct or not? Does it have to be the same as the LAN IP Address?)

    Nope. Should be the same as Globe's modem LAN which is 192.168.254.1 to 192.168.254.253.


    NAT: ON (Guessing here. Not sure if it will cause double NAT issues. Please comment.)

    Yes. Important.


    UPnP: ON

    FIREWALL: IPv4 IPv6: ON

    Internet Connection: through Static IP

    UPnP: ON (but recommended OFF.)
    Yes correct.
    So this is what your WAN settings on your router should look like:
    Protocol: Static IP.
    WAN IP Address: 192.168.254.100
    WAN Subnet: 255.255.255.0
    WAN Gateway: 192.168.254.254
    Primary DNS: 1.1.1.1
    Secondary DNS: 1.0.0.1
    (If you want Globe's own DNS then remove secondary DNS and set Primary DNS to 192.168.254.254.)


    1) Do I enable the DHCP on BOTH the main modem/router (ie the ZTE ZHXN H108N) and secondary router (TP Link AC2300)? Will it conflict each other? What range should I put on both? Does it have to be very different IP address range?

    2) Will connecting two routers caused double NAT? Will that even be an issue?

    3) How about Voip? Will it be effected?

    4) How about the UPnP? Do i enable it on both or none?

    5) What internet connection type do I choose on the secondary router TP Link AC2300 since it offered 5 types (Dynamic IP, Static IP, PPPoE, L2TP and PPTP)?

    7) Should I turn off the wireless radio on the ISP modem/router (ZTE)?

    1. Yes but can be no for main modem. But for less hassle let's leave it on. Secondary router yes its a must since that's giving your connected devices network settings to browse/use internet without configuring other than setting up wifi password.

    2. It will. With right config that would not be a problem. Since DMZ is at work here we effectively ignore firewall settings on Modem and your TP-Link will be handling it. Ala "bridged" mode.

    3. Voip will not be affected since we just turned on a switch sa modem (DMZ) without changing ISP configuration.

    4. If u want you can enable it. But enable it on your TP-Link only.

    5. So as stated above: Static IP. (Dynamic IP will work since we did not turn off DHCP as stated on question 1, unless you want control).

    6. What is your use case? If you want everyone to use your TP-Link then yes turn off the wireless radio on your ISP modem. (they're shit anyway).
  • oh wow, thanks EALIFE. Appreciate. Will give it a try.

    By the way, would you recommend just Bridging or DMZ?

    If so bridging, how to do it?
  • Strangely the ZTE modem router doesn't allow me to bridge it. Whenever I set the parameters, it will revert to the previous parameters.
  • Tried to bridge it but somehow the ISP router do not save the setting. See this video for what I mean https://youtu.be/Ym9GWNcZn4M
  • Hi question lang, ganun ba talaga fiber ni globe. Pag 5g wifi 100+mbps pero pag 2.4ghz half the speed lang
  • ^

    more or less tama yan. could be worse if congested na ung 2.4g sa area nyo
  • Globe came in today to fix this "broadbandstatus2" redirect problem. they fixed it. but I lost my static/public IP. now i'm having CGN/private IP of 10.120.171.x

    haist!

    nakabind pa naman ito sa cloudfare config ko for my webserver. hassle!
  • @jovenxp
    di aabot ng 100Mbps ang 2.4GHz kahit itapat mo pa device sa router.
  • @newbie same tau gusto ko sana ngaun ipacheck kasi after mag broadbanstatus2 ung akin bigla ang hirap amg loading ng facebook. ehh naka static ip ako. pano nila inayus?
    a day before nangyari eto sakin. tumawag ung customer service sakin na upgrade ko daw ung 50mbps ko into unli data. pero 2500 lang daw babyaran ko ehh 1899 monthly ko 600gb parang strategy nila eto

    -- edited by blazeservice on May 02 2019, 09:52 AM
  • Good day!

    Pwede malaman kung ilan ang upload speed ng 10/15/20mbps (1899) ng GLOBE dsl niyo? May mga taga san pedro laguna area ba dito? ano feedback niyo pagdating sa games(pubg mobile/ ML/etc)? ano din pala ibig sabihin nung 10/15/20mbps sa website(naglalaro diyan ang download speed)?

    Thanks nagbabalak bumalik galing Sky. wala kasi fiber dito kaya no choice kundi dsl pa din(either pldt or globe).
  • ^

    Ako San Pedro Laguna sir.

    1899 20mbps VDSL Plan



    ML = 20-30
    Real PUBG = 30-70
    Dota 2 = 30-40
  • @blazeservice, hindi ko sure kung paano nila inayos yong portal redirect.

    nakasampung tawag yata sa tech center nila. so ayun, naayos nga. nawala naman static IP ko. di pa rin -nababalik, kahit araw-araw ako tumatawag since Tuesday.
  • ^ based sa experience ko is mali ung credential naka sa set PPOE mo.
  • ^ based sa experience ko is mali ung credential naka sa set PPOE mo.

    may internet naman sir... yong public static IP address lang ang nawala.

    also, pinaliwanag ko din yan. na pinalitan nila ang username and password ko. na baka may hindi na-sync sa configuration etc.

    ang datingan sakin na explanation nila ay para bang pabayaan mo kami, hindi yong mas marunong ka pa samin :D
  • ^ nawala static IP mo kasi na reset ung PPOE account mo, there's something wrong sa config on their side.

    On set pa lang ng call pa ramdam mo sa kanila technical ka, para di ka ma bully or ma uto ng mga CS.. ganyan ginagawa ko para walang daming palusot.
  • Quesiton:

    I am currently subscribed to Plan 1299 5mpbs 500gb (dsl), I am planning to upgrade to plan 1899 20mpbs unli fiber plan. Would it be possible to upgrade without the pre-termination fee?
  • ^

    Plan upgrade = back to zero lang ulit ang counting ng lock-in period

    example, kung sa current plan mo ay 6 months ka na, pag nag upgrade ka, back to 0 lang ulit yan

    If mag opt out ka naman during lock-in period, papabayaran lang sayo router fee
  • @gowueld

    Ohhh. So it means pati freebies makukuha ko ulit? Like Netflix etc
  • ^

    I suppose yes, pero clarify mo rin sa kanila para makasiguro ka
  • Ohhh. So it means pati freebies makukuha ko ulit? Like Netflix etc

    nung pinalipat ko yung connection ko to a different address, they treated it as a "new" contract. nagreset yung contract ko for another 24 months. after a few days, i started receiving the freebie emails (hooq, disney life, etc.)

    ps. hindi na sila connected sa Netflix. (HOOQ, FOX+, iFlix, and Amazon Prime Video, DisneyLife makukuha mo)
  • May issue ba globe? Bagal magload ng facebook at streaming pero ok sa speedtest. Cavite area Imus
  • ^

    Mukhang may problem ata, nag time out sakin, intermittent pero hindi nag didisconnect.

    San Pedro Laguna area ako
  • Mukha nga. Ok speedtest ko eh pero bagal magload ng images sa facebook. Sa youtube ok naman pero ung NBA league pass medjo mabagal. Hmmm
  • nagloloko din globe dsl ko, bulacan area

    puro time out ang ping and mabagal download. kanina lang umaga, mga 9am nag start
  • May public Advisory na ang globe may na cut daw na wire sa quezon buong pilipinas affected

  • nag loloko din sakin q.c area and dun sa tropa ko bulacan area