Forum Topic

Tomato flashed Dual wan Router from CD-R KING (CW-5356U/CW-5358U) Read Page1

  • ^ per IP = yes

    per port = yes and no

    no = if no vlan
    yes = if meron vlan with their own subnet (caveat, hindi magkikita yung mga devices na connected sa mga port na yun).
  • @polka
    yung tomato ba natin pwdeng iremote access yung router? purpose pra lng ireboot/restart?
    kung pwde papaano!
  • ^ via port forwarding.
  • go to administration >> admin access

    theres a remote access option there, set it to http or https and set the port.

    -- edited by polka on Jan 11 2018, 08:29 PM
  • @iced
    dapat lang hindi ka naka cgnat.
  • @frequenzy
    paki elavorate sir!
  • ^check your wan ip

    if your ISP assigned you with 10.xx or 192.168.xx or 100.xx
    then your under CGNAT
    with CGNAT you cant open ports
    and that leads to blocking incoming connection

    in short, you cant remotely control anything under cgnat, thus making it impossible to control anything on your tomato firmware. or anything that requires port forwarding, like cctv, game consoles like ps4, xbone requires port forwarding or else hindi kayo magkikitaan (0 players) etc....
  • ahh... ok! s linksys kasi nkkremote ako kahit private ip pa ibigay sa akin ng isp ok.
    akala ko may work around without paying heh thx.
  • mga master I'm planning to use 5538u as wifi. nagddrop kasi wifi ni PLDT Onu so gagamitin kong wifi ni 5538u. nag try ko ikabit yung Lan1(onu) to Wan ni 5538u. kaso walang internet access. kailangan ba talaga nka bridge mode? or pwedeng hindi.

    1.28 shibby version ni 5538u.

    thanks mga lodi!
  • ^disable mo yung DHCP server ng tomato, then set mo yung ip address ng tomato under the same subnet ng fiber router mo, then kabit mo sa lan port ng kamatis yung lan connection galing sa fiber home router mo.
  • ^disable mo yung DHCP server ng tomato, then set mo yung ip address ng tomato under the same subnet ng fiber router mo, then kabit mo sa lan port ng kamatis yung lan connection galing sa fiber home router mo.


    thanks sir polka ok na sir!
  • Hi sir polka. question lang. nawalan ng internet access yung isang desktop ko na nkaconnect sa lan ng fiber router. pero pag nka connect sya sa lan port ni kamatis meron naman.
  • OT

    LEDE and OpenWRT are now merged / merging!

    EDIT:

    Just updated my DLINK DIR 615 to latest stable openwrt (LEDE build)


    Hostname dlink-lede02
    Model D-Link DIR-615 rev. C1
    Firmware Version LEDE Reboot 17.01.4 r3560-79f57e422d / LuCI lede-17.01 branch (git-17.290.79498-d3f0685)
    Kernel Version 4.4.92
    Local Time Mon Feb 19 19:40:35 2018
    Uptime 0h 13m 41s
    Load Average 0.02, 0.10, 0.09



    -- edited by ryanrudolf on Feb 20 2018, 08:43 AM
  • bro, login to webconfig ng router then dun mo na ireboot/restart yung router mo
  • @all - question po, may updated list po ba ng routers na compatible sa tomato?

    http://tomato.groov.pl/?page_id=69 - ito kasi parang hindi na ina update

    nahihirapan kasi ako maghanap nitong mga router na gusto ko

    - Asus RT-N18U v121 or newer (ang hirap bumili nito, kasi ayaw buksan yung kahon para macheck anong version sha)
    - Linksys EA6500 v2
    - Linksys EA6700

    yung 5358u ko kasi feeling ko pasira na, malimit na bumitaw yung wifi, pag bumitaw yung wifi nya need mo na sha ireboot.

    TIA
  • Anyone able to update to a newer version for CW-5358U? especialy on Guest WiFi or Virtual Wireless option?
  • ^well as long as the guest wifi has a access to the web interface, sure you can but we dont recommend it as it can potentially brick the router due to potential corruption of firmware uploaded via wifi (given how unreliable wifi now is due to 2.4ghz noisy network).
  • Pano to i set up using windows 10? Yung i-connect ko yung pldt modem to this router. Nakalimutan ko na kung paano since ngayon ko lang ulit nakita to. Thanks in advance.

    -- edited by jeff_3429 on Mar 15 2018, 11:25 PM
  • Post deleted #12106432
  • mga idol baka sakali may interesado sainyo libreng network basics webinar check nyo na lang sa Facebook: <click here for link>
  • Sir polka, anong firmware gamit mo ngayon? Kakakuha ko lang ng PLDT fibr and may existing dsl din ako. Any insights on using dual wan with this setup? Possible ba na for some devices main connection is DSL tapos failover ng fibr yung DSL for the devices connected to it?
  • ^you can use the dual-wan firmware, and try using the the multi-wan routing. although i have bad experience using it.

    @all

    I tried using this rusty cw5358u as a standard managed switch + ap.

    using a HP thin client with pfsense installed (only 1 NIC)

    flashed the daking router with latest multiwan firmware (since it greatly improved the VLAN page settings compared to old firmware eg, you cant have 1 port to have untagged and tagged vlan on it)

    my VLAN settings.

    Port Arrangement

    WAN Port = WAN port
    LAN1 = Port 4
    LAN2 = Port 3
    LAN3 = Port 2
    LAN1 = Port 1




    LAN2 LAN3 LAN4 WAN and WiFi1 is binded together and untagged (this is where the LAN is plugged in)
    Tagged WAN and WIFI2 is binded together and tagged as VLAN10 (WiFi rental)
    Tagged WAN and untagged LAN1 is binded together and tagged as VLAN11 (modem)

    Wifi 1 is binded together with LAN network (encrypted)
    Wifi 2 is not encrypted (open network) assigned as wifi rental

    setup, WAN port is directly connected to pfsense and LAN1 is connected to modem. LAN2-3 ports and WiFi1 is LAN access, WiFi2 is Captive Portal WiFi rental.

    pfsense setup:
    create vlans with vlan10 and vlan11
    vlan11 assigned as wan
    re0 assigned as LAN
    vlan10 assigned as opt1 (captive portal)

    created additional opt1 rules to restrict access to LAN network only internet access
    create a new captive portal and assigned opt1 as interface for the portal, designed the portal with little to basic html skills on basic photoshop, downloaded a opensource app vouchermanager <click here for link> and configure voucher to generate codes using the app (no more thinkering on pfsense webadmin), all with max speed of 512kbps download and 120kbps upload (naka globe lang sya eh DSL, may data cap pa na 400gb) with denominations of 5 10 20 50 and 100 (5 10 and 20 is hourly while 50 is 1 day and 100 is 3days), pang rules of survival ng mga bato doon.

    initial results works as expected. they using it on piso net with wifi rental with voucher.

    I also maxed out the Transmit power of the wifi to 250mw (max based on specsheet of BCM5356) and also plugged it using a USB to barrel jack, supplying 5volt power to cw5358u.

    Total power consumption overall is 23watts. modem+thin client+cw5358u
  • Mga sir gamit ko yung ripantows na qos sa 1st page bale yung youtube app at youtube di sya working once na nag start mag youtube sa bahay nag lag na ako pano po malaman yung port nun
  • Post deleted #12129463
  • @polka
    na try mo n ba sa tomato yung usb printer? papano paganahin yun?

    ex: 192.168.1.1 makikita n n may printer shared?
  • Mga sir gamit ko yung ripantows na qos sa 1st page bale yung youtube app at youtube di sya working once na nag start mag youtube sa bahay nag lag na ako pano po malaman yung port nun

    hindi na ata gumagana yung l7 filters na specific sa youtube, youtube also uses http port 443, same as browsing. so mahirap gamitan ng port based qos dahil maapektuhan yung browsing mo.
  • @polka
    ok na di pla pwde ang epson L110 d nadedetect
  • Help sirs! I recently flashed using this fw tomato-K26USB-1.28.RT-MIPSR1-130-BTgui-VPN. I tried through the GUI pero after upgrade di ko na maaccess 192.168.1.1 or 192.168.11.1. Tried the tftp upgrade path and it showed that the transfer was successful. Di ko pa rin maaccess yung GUI through both ip addresses.

    PC connected sa LAN 2-3 di pa din maaccess. Weird din walang wifi connection

    -- edited by migsvill on Jun 20 2018, 01:17 PM
  • @mig
    mali yung ginamit mong firmware, try mo to
    tomato-K26USB-1.28.RT-N5x-MIPSR2-128-BTgui-VPN
  • Sabi na may mali e hahaha. Thank you sir!

    -- edited by migsvill on Jun 20 2018, 02:10 PM