Forum Topic

Official Networking Thread (LAN Configuration, Internet Sharing, Routers, Switches, etc.)

  • sino po may expertise or familiar sa fortigate appliance?
  • Post deleted #12111754
  • Archer C7 na ba best bang for the buck router available currently?

    Upgraded to gigabit, kailangan na i-retire yung Xiaomi wifi mini ko dahil 100mbit WAN/LAN lang.
  • Patulong naman po.

    May prolink po akong modem router, paano ko sya maseset as modem lang then yung cdr king na router ko po gagamitin ko. Wala kasing qos yung sa pldt dsl modem router eh. Salamat po.
  • pag may na detect ba kong mac address coming from 2 different physical port on my coreSW it means my loop or my iba pang possible scenario.
    im running standard rstp with multiple vlans in my network coresw as the gateway with default routes pointed to my firewall/router.

    @geno
    ako medyo my exp kahit konte.

    -- edited by maxblaze13 on Apr 15 2018, 03:11 PM
  • @ maxblaze13
    @ all

    eto kasi scenario sa office. sa fortigate firewall namin may 2 ports kami utilized. port 1 may managed switch then andun connected lahat ng pc na need ng unrestricted internet access. port 2 naman blocked ang social networking sites.

    problem is may 2 pc sa isang room, one connected the port 1 ng firewall while the other sa port 2. need nila mag share ng printer (epson L360). di ko sila pede pagsamahin sa isang switch. ano workaround dito? i'm thinking vpn but i haven't tried that yet.

    purchasing another printer cannot be done as of the moment.

    -- edited by gen0 on Apr 16 2018, 03:47 PM
  • ^ nasan yun gateway nang 2 pc? Sa port 1 at port 2? Kung zone based fw yan fortigate nyo, need mo gumawa ng interzone rule para makapag connect yun mga clients mo na nasa port 1 at 2.
  • 1)assuming na network printer gamit nyo
    2)assuming naka static ip ung network printer
    3)assuming dhcp enabled ung 2 pc
    4)assuming printer is in port1 of firewall

    - reserved the acquired ip of the 2 pc sa dhcp.
    then create policy
    source: port2
    source IP: pc2 IP
    destination: port1
    destination IP: PrinterIP
    move up the policy.
    then same concept kung si printer nasa port2 namn.

    or to make things simple create ka ng 2 policy pra magkita ung 2 subnet on firewall.

    -- edited by maxblaze13 on Apr 16 2018, 04:33 PM
  • pag may na detect ba kong mac address coming from 2 different physical port on my coreSW it means my loop or my iba pang possible scenario.
    im running standard rstp with multiple vlans in my network coresw as the gateway with default routes pointed to my firewall/router.


    @maxblaze
    yung 2 different physical ports trunk ports ba yun? kung same mac address nakikita galing sa 2 different ports posible may loop, check mo yun coreSW nyo kung may amber lights or sabay2 nag flash ng led pati naren cpu utilization kung mataas.
  • sorry medyo magulo kwento ko. here goes:

    eto yung network before.

    <click here for link>
    PC 2 has a printer connected via USB, PC1 and PC3 connects to printer of PC 2 via lan. due to company policy, PC 1 and 3 has to be connected to the other switch but still needs access to PC 2's printer.

    <click here for link>

    * printer has no ethernet/wifi
    * PC 1, 2, 3 are 20 meters apart from each other

    -- edited by gen0 on Apr 17 2018, 10:24 AM

    -- edited by gen0 on Apr 17 2018, 10:25 AM
  • Need mo lang mag create ng security policy or rule sa firewall nyo para mapagkita mo yun mga clients sa switch1 at 2.

    kung may support license pa yan firewall nyo at natatakot ka kalikutin, much better itawag mo nalang sa kanila, sila na titira nyan he he
  • ok lang naman kalikutin. gusto ko lang sigurado sa unang tira. hehehe

    di ba affected yung internet policy nila kung mag zoning ako?
  • anong model ng fortigate nyo? wag mo lang i-edit yun rule para sa internet and kung mag add ka nang rule below dapat nun at above ng explicit deny rule nyo
  • fortigate 100D
  • Hello guys, I'm running a Networking Basics webinar series. Kung gusto nyo magjoin pm nyo lng ako :)

    First webinar is next Friday April 27 - 7-9pm.

    Part 1 of 5 in the series

    The Networking Basics webinar series is composed of the following topics:

    - Intro to Networking - Understanding the Layers of the Network
    - Network Layers - The Deep Dive
    - Basics of Switching
    - Basics of Routing
    - Stay tuned (TBA)

    Expected outcome: from beginner to solid networking fundamentals once you complete the series

    Example topics (from webinar 2 Network Layers - The Deep Dive)

    Layer 4 - transport
    TCP
    - session management
    - retransmission / reliable delivery
    - flow control
    - segment reassembly
    - congestion avoidance
    - 3-way handshake
    - acknowledgements
    - TCP flags
    - sequence numbers
    - TCP windowing

    This webinar series is FREE
  • Mga masters mga bossing.. pasuggest naman po ng exact model cisco switch and router na maganda gamitin for studying ng CCNA ung di maxado kamahalan..salamat po sa sasagot..
  • Mga sir question po, i hope matulungan ninyo ako sa inquiry ko po
    Bale naka PLDC Fiber ako at current setup ko is

    ONU (Bridge Mode) > TPLINK (Main router pang QOS) > 2nd TPLINK router pandistribute ng signal sa kapitbahay na nagbabayad sakin.

    Bale ang gusto ko po kasing mangyari eh malimit ko using QOS ung bandwith para sa 2nd TPLINK router ko na nakalagay sa bahay ng kapitbahay.

    Question san ako dapat mag set ng parameters para sa QOS for kapitbahay? Sa 2nd TPLINK router naba kaagad? Or pwede ko bang i QOS (yung 2nd TPLINK router) via IP address using 1st TPLINK router (which is main) ??

    Sorry po if medyo magulo. Bale gusto ko lang po malimit o macontrol bandwith ng mga users connected under 2nd TPLINK router. Salamat po
  • @vicmanhid

    Sa Main TP link

    PLDT bridge to blue/wan ng TPlink Main then to blue/wan ng TP link 2nd

    TPlink main
    WAN IP DHCP(IP provided by PLDT).
    LAN IP 192.168.1.1

    TPlink 2nd
    WAN IP 192.168.1.2
    LAN IP 192.168.2.1

    Configure IP QOS for 192.168.1.2 sa TP link main
  • @Blu3martini

    Salamat ng marami sa comment mo sir ill try kagad pag uwi ng bahay (nasa office pa kasi)
    Eggcited nako sana gumana,
    Maraming salamat po ulit

    Thumbs up!
  • If tama ang pag kaka intindi ko,

    1* from PLDT ONU port number 1 to Main TPLINK blue/wan then, Lan1 ng Main TPLINK to blue/Wan ng TPLINK 2nd?

    2* from PLDT ONU bridged using lan 1 to Main TPLINK lan1, then Blue/Wan ng Main TP ling to Blue/Wan ng TPlink 2nd?

    (Please tell me if tama ba ang pagkaka intindi ko and if ano sa dalawang options ang tama)

    Then set ng ganito
    -
    TPlink main
    WAN IP DHCP(IP provided by PLDT).
    LAN IP 192.168.1.1

    TPlink 2nd
    WAN IP 192.168.1.2
    LAN IP 192.168.2.1

    Configure IP QOS for 192.168.1.2 sa TP link main
  • @vicmanhid

    1*
  • @Blu3martini

    Thank you po marami.

    Naiset up ko na routers ko sa bahay so far so good maraming salamat po sa feedback ninyo.

    _

    Another inquiry if mapagbibigyan, SInce ang setup ko currently is
    PLDT fiber (bridged mode) > TP link 1 (Main) > TP link 2 (personal kwarto)

    Sa TP link1 main, naka connect ang sumusunod ,
    *cctv
    *mobile phones sa bahay (ina ate kuya kapatid )
    *TP link 2 (personal router sa kwarto)

    Since ang IP address ng TP link main router 1 is 192.168.0.1 (ang starting ng ip ng tp link1 ko is 192.168.0.110 to 192.168.0.150)
    kapag naglagay ako ng QOS default sa tplink router 1 ko na 5 mbps, ang problem ko is sa PC ko which is connected to Tp link2 is getting 5 mbps lang rin though ang ip nya is 192.168.0.2 which is wala naman sa ip range ng main router na 192.168.0.110 to 150.

    Paano kaya ito?

    Salamat po
  • Check your QOS config.

    I think yung 192.168.0.110-192.168.0.150 mo is DHCP lease hindi range ng QOS.
  • New Xiaomi Router 3 User
    Ayos na Ayos sa Bandwith Control at Guess WiFi
  • Post deleted #12118314
  • Good day mga sir.
    Another inquiry po salamat newbie po kasi sa PC networking.

    Ang set up ko po sa bahay ay (Lan to Wan)

    Bale may tatlo po akong network
    - Net SSID1
    - Net SSID2
    - Net SSID3

    *PLDC ONU Bridged Mode 192.168.1.1
    *Router1 192.168.0.1
    *Router2 192.168.2.1
    *Router3 192.168.3.1

    Sa Router1 po naka connect
    -cctv
    -mobile phones ng mga tao sa bahay
    -Lan to Wan ng Router 2

    Sa Router 2 ay naka connect (Second floor)
    -PC ko/ and cellphone

    Sa Router 3 nakaconnect
    -naka kabit sa lan ng Router2, to Wan ng router 3 since ito ay nasa kapitbahay (nagbabayad sila ng fee para sa net monthly)
    -gadgets ng kapitbahay

    Since naka connect ang PC ko sa router 2 (192.168.2.1)
    bale na aaccess ko ang Router1 (192.168.0.1) though medyo na OOC ako at di ko maaccess ang Router3 (192.168.3.1) .

    Ang ginagawa ko lang na temporary work around is i plug directly sa pc ko ang ethernet cable ng router3 na connected sa router 2.

    Question, Meron po bang paraan na ma access ko ang Router3 (192.168.3.1) even if connected directly hard wired ang PC ko sa router 2 ??

    Di po kasi applicable ang lan to lan setup sa akin since iba iba po ang traffice management ko sa para sa mga gadgets sa bahay, compared sa PC ko, pati sempre sa gadgets ng kapitbahay which is sa router3.

    More power po at salamat
    I hope me sense po ang tanong ko.

    :)
  • ^router3 has a firewall and for (obvious) security reasons access to admin page of the router via wan is restricted.

    to access the router's admin page via wan will depend on the router if it supports it or not, you can just assume that its not supported so yeah......
  • Thank you po sa reply.
    Nkapag search rin po ako ng additional ke google while using company resources idle naman hehe,
    most of the time raw kapag Wan to lan ang setup di mo ma access ang isang modem (most probably because of security reasons).

    Anyway mag stick nalang muna talaga siguro ako sa pag kabit ng ethernet cable ng Router 3 directly sa pc ko para makita ko ang admin settings ng R3
  • bakit hindi maka connect ang laptop Lenovo G500 gamit kong Os windows 8.0
    sa PLDT wifi modem ProLink PRS1241B?
    kaya gumagamit pa ako ng router para maka connect sa wifi ang laptop.
    Atsaka hindi ma read ni laptop ang modem gusto ko sana palitan ng password.

    hayzz
  • ano issue kung napiping ng client ang server pero not the other way around