^
Definitely fabricated. Probably a mix of wood and metal.
Forum Topic
Post your MacGyverization here (Crazy Mods/Quick Fixes that works)
-
Uu ngA parang hirap ng cabling nyan
Sana mahanapan nyo ng paraan -
^
There might be a hole where the pivot is, big enough for the power and HDMI cables.
Also, I think that it only rotates 180 degrees and not freely rotating. Otherwise the cables would get twisted.
One problem I see is the lack of ventilation holes. -
eto kelangan mo , yung heavy duty , pang upuan lang kasi ito.
return swivel ang tawag.
-
^ Doesn't solve the cable routing issue. IMO the pivot itself could be made from tubular steel pipe at least 1.5 inches in diameter. There would be a small notch at the pipe, and with a corresponding notch on the frame to limit the rotation angle.
-- edited by awakeruze on Oct 22 2018, 06:24 PM -
Thanks sa reply guys, i found a solution regarding cable management.
<click here for link>
-- edited by krauzergtx on Oct 22 2018, 07:02 PM -
hindi ako sure kung pasok sa thread na ito.... pero nag modify ako ng 10x330mm pneumatic belt sander para umandar sa 12V motor.....
nakabili ako ng ryobi airwave belt sander RABS330 for 200 kasi plano ko nang matagal na lagyan ng 540 type 12V motor dahil wala ako compressor pero gusto ko ng manipis na belt sander... eto pics
bali drilled the end cap for the bolt holes and the shaft and adaptor tapos yung adaptor ginawa ko lang para maikabit yung motor dun sa shaft ng belt sander... yung laman loob ng belt sander tinanggal ko lahat maliban dun sa bearing at bearing carrier. yung dalawang itim na yan plastic spacers na super glued to the end cap para tama lang ang spacing ng motor sa belt shaft... bilhan ko pa ng switch at wiring pero tested na sa 12V power supply.
-- edited by redwing0001 on Nov 21 2018, 11:29 PM -
^
More pics. I want to see the end result. :D -
Wiring is finished..... kulang na lang yung pagkabit ng end electrical plug....
Itong link nung buong album ng DIY: <click here for link>
pag ayaw copy/paste sa web browser niyo: http://s198.photobucket.com/user/redwing0001/library/DIY%20Ryobi%20pneumatic%20belt%20sander%20conversion?sort=9&page=1
-- edited by redwing0001 on Nov 22 2018, 11:55 PM -
Nice mod. Hope it works well. :D
Today's hack(?) or more like emergency surgery-- friend accidentally put the SIM inside his iPhone without the SIM tray. We managed to pull it out using two sewing pins. :D -
sanding belt na lang kulang lalarga na... meron dito malapit sa akin na distro mismo at gumagawa ng sanding belts.... kuha ako sa kanila ng 12x330mm cloth belts na maganda quality.
friend accidentally put the SIM inside his iPhone without the SIM tray.
yung nokia 3310G nailagay ko yung nano sim, e microsim lang pala siya... perdible din ang sagot sa pag kuha ng mga sim na ganyan. -
gumana na yung belt sander..... pero kelangan ko palitan yung unang RS550 motor dahil nag fail yung motor.... matanda na kasi at uminit na nung ginamit ko siya. Buti na lang meron ako isa pang RS550 na motor na pede ko gamitin.
nag mod pa ako para bawasan yung armature para maikabit yung rear bearing para meron support yung armature at motor. kelangan talaga lagyan ng bearing dun. nakabili din ako ng sanding belt na pedeng gawin kong sanding belt... 10x330mm siya tapos bumili ako ng ibat ibang pandikit at tela para maikabit ko sa likod ng sanding paper.
bumili ako ng cloth adhesive, shoe goo at dalawang tube ng shoe glue, bulldog at pioneer... basta may cloth backing dun sa sandpaper, kahit anong glue pede at matibay naman pala. -
same mod ni sir ututin1, lumabo na din yung reading ng LCD.
my cheap 10yr old generic multi-tester, 150.00 petot yata bili ko dati.
Aluminum foil tape ginamit ko, wala ako pic ng before mod, pero dinikit ko yung old aluminum foil for comparison.
may sentimental value kasi ito sakin, ni-convert ko to 10years ago para kaya ang 30-40amps reading para sa kaadikan ko sa RC Plane, cheap DIY wattmeter.
-- edited by razor on Nov 30 2018, 11:03 AM -
Plug-n-play bios mod (Lol) sa laptop na ayaw mamatay.
-
Care to explain what it's supposed to be doing?
-
Pardon me guys. It's my SAMSUNG NP300E4C that has been EFI locked and i can't get to BIOS so I ordered a CH341a bios programmer and used flashrom just to recover it. The problem is the bios cannot be flashed habang nkakabit sa board kaya gumawa ako ng adhoc wiring using a broken sdcard reader and sdcard adapter, wired it to a board where i soldered the bios then wired the board to the SDcard reader. With that, hindi na ako solder/desolder when bios flash fails, i just unplug, flash, then replug it and when i get locked again sa EFI screen i can just simply repeat the flashing.
-
That's one crazy mod/repair.
So the wires from the SD card slot go to where the ROM flash chip used to be?
EFI locked? so there's some kind of fault in the firmware? have you tried replacing the flash ship itself? -
Yes it's a known issue with samsung np300 and similar models and flashing lang ang makakaayos. Wala ako donor board eh walang kapalit. 8 wires from the pads on mobo wired to sd card reader then same with the sd card adapter. It's crazy man. kala ko kaput na nung hindi nag-on first time but some bad connection lang pala. Napraktis ko din smd soldering haha
UEFI lock pala not EFI.
-- edited by rufnek on Dec 08 2018, 01:34 PM -
I'm happy to report that I've succeeded in replacing the 3x AAA battery pack in my CD-R King Iris LED flashlight <click here for link> with a single 18500 Li-Ion cell-- it's the same diameter as the common 18650 Li-ion cell, but a bit shorter (same length as an AA battery).
No need for spacers or extensions. The spring contacts on both ends hold it pretty securely.
:D
I was originally going to use a 14500 cell (exactly the same size as an AA battery, but it's 3.6-3.7v like most Lithium cells), but changed my mind upon seeing its low capacity -- only 750mAh compared to 1500 for the 18500.
-- edited by awakeruze on Dec 14 2018, 04:05 PM -
gitna ng tissue ginawang stand ng 750ti para nakatutok ang 120mm fan sa card..inalis ko shroud and fan ng card :) merry Christmas po sa lahat :)
-
Yung 6ft Christmas tree namin na fiber optics na sobranginit dahil sa ilaw nya sa ilalim ay halogen ay muntik nang masunog. Ang ginawa ko ay pinalitan ko ng LED yung ilaw sa ilalim. Naging mas maliwanag pa at nakatipid pa ako ng sa kuryente at kahit walang patayan di man lang umiinit kapag hahawakan yung base.
-
Bumili ako ng malaking bintilador na industrial fan. Bagamat bago siya malakas yung resonance nya kaya maingay. Tinalian ko ng bakal na mabigat. Malaking pliers ang ginamit ko at pinorma ko siya na ornate para di mag mukhang dead weight. Completely na-cancel nya yung resonant frequency kaya super quiet na sya. Bakit maingay yung na fan yung binili ko? Kasi di 100% metal yung body nya kaya nagresonance sya. Masyadong malaki yung mass ng blade assembly kumpara sa stability ng base nya. Konting ingay lang naman pero parating napapansin kaya ginawan ko sya ng hack.
-- edited by DjDom2 on Jan 01 2019, 03:20 PM -
DIY Spring mouse holder
1x Speaker Magnet base
1x Long Spring
Tie Wire
Epoxy Glue
-
^
Astig! :D - Post deleted #12207818
-
Recycling my old broken laptop's lcd with a lvds driver from laz.[url][/url]
The board:
result:
Native resolution ng lcd is 1280 x 800 pero walang jumper for that ang meron closest is 1360 x 768 so sablay yung display but usable. Need ko pa i-reconfigure yung LVDS cable for my lcd model. It was fun weekend project. -
^
Plan to do the same in the (hopefully) near future. Can you PM me a link to particular item you bought? -
Link: <click here for link>
have the datasheet for your lcd ready - save you the headache later. -
@rufnek
It has VGA input only? It would have been better with more inputs like HDMI/DVI.
Does it come with a LVDS cable, or do you have to make one yourself? -
@awakeruze
Mine has only vga but other drivers are available with HDMI/AV like this one <click here for link> mas mahal nga lang.
LVDS cable included but double check with your model if kasama. I have to re-config the pins for my LCD as per datasheet.