-
comp071
on
12 Feb 19 @ 10:40 AM #
@bobby1970
good pm po, bago lang po ako dito, magpapatulong po sana ako kung papano pag troubleshoot or repair ng AOC 18" LED Monitor, shaky po kasi yung screen, nanginginig sa paningin, nagpalit na ako ng monitor ok naman yung pinalit ko, baka po may marunong magrepair patulong naman po, wala pa ako pambili ng bago madami pa gastos mga bata sa school, salamat po..
palagay ko lang yung lcd panel na sira nyan mas mura pa bumili ng 2nd hand kesa pa replace mo yung lcd panel nyan
-
maxikurt
on
12 Feb 19 @ 08:21 PM #
Good day po! Ask lng po sana ako ng tulong with mikrotik router configuration for mikroticket? TIA!
-
bobby1970
on
13 Feb 19 @ 11:17 AM #
salamt comp071..
-
awakeruze
on
13 Feb 19 @ 12:38 PM #
@maxikurt
You might want to ask in other threads, this is one is not specific to LAN/router issues, like the Microtik thread
<click here for link> or the official networking thread:
<click here for link>.
-
seanne
on
13 Feb 19 @ 09:53 PM #
Hi Guys,
Going back sa problema ko before. Whenever i enable the XMP profile, nag boot loop sya. Below are my rig spec;
CPU: i5 - 8400
RAM: TridentZ 2x4 3200Mhz
Mobo: Gigabyte Z370M D3H (With F10 BIOS version)
Whenever XMP Profile is enabled, nag oopen naman sya kaso after a few seconds nag BSOD then nag reboot loop na (as in patay sindi lang yung ilaw sa rig). Naayos ko naman sya nung naka pasok ako sa BIOS at dinisable ko yung XMP profile (currenly running at 2133Mhz), so far stable sya if within this speed lang. Kaso syempre, i want to get more out of my hardware.
Meron na pala BIOS Update (F11c) kaso im hesitating to update and try to enable XMP profile kasi baka di nako makapasok ng BIOS at di ko na ma-disable yung XMP.
I'm not sure kung alin yung sira, is it the RAM or the Mobo? Planning to replace the faulty component asap para naman makuha ko yung worth ng item.
Any help is appreciated. Thank you TPC fam!
-- edited by seanne on Feb 13 2019, 09:56 PM
-
awakeruze
on
13 Feb 19 @ 10:20 PM #
^
Stick to 2133MHz, then run the BIOS update.
If you need to disable XMP but can't enter BIOS, it may be easier to just remove the CMOS battery.
Correct me if I'm wrong, but AFAIK XMP must be manually enabled, so if the CMOS data is reset, it will default to the normal (and safe) RAM settings.
-- edited by awakeruze on Feb 13 2019, 10:21 PM
-
seanne
on
13 Feb 19 @ 10:52 PM #
@awakeruze
Hi Sir, just for confirmation...
You want me to stick at 2133Mhz then update the BIOS. After that, do you want me to enable the XMP profile to test if the RAM would run at 3200Mhz?
If by any chance that my initial problem happened again, what i need to do then is to clear the CMOS batt for it to reset to its default RAM settings. Correct?
-
CrkDice
on
13 Feb 19 @ 10:55 PM #
^sang ram slot po nakalagay yung 2 sticks, and natry nyo na i manual set yung timings based on default timings nakalagay sa ram sticks?
-
awakeruze
on
13 Feb 19 @ 11:05 PM #
@seanne
Yes.
Well, just to be safe, you could run a RAM test like memtest86+ to ensure that the RAM is stable at 2133MHz. Let it complete 2 passes. If no errors are detected then you can proceed with the BIOS update.
-
seanne
on
13 Feb 19 @ 11:17 PM #
@CrkDice
Di ko lam tawag dun sa slots. haha. Let me explain it on my own terms, from left to right "Black-Gray-Black-Gray" slots.. dun sya nakalagay sa gray slots. hehe.
@awakeruze
Will definitely git it a try when i get home. :)
Thanks guys!
-
calmaardee
on
15 Feb 19 @ 10:05 AM #
Gud am mga ka TPC hingi lang ako ng opinion nyo, bumili po kasi ako ng bagong parts ng pc eto po mga parts i7 8700k,asus z390 strix E,ram Gskill 3600 royal 16gb at corsair h115i, at ang ginamit ko na psu para dito seasonic 750 x series na gamit ko dati sa luma ko, merong lumalabas na tunog dito noon pa mga 2 years na siguro hinayaan ko nalang dahil ok naman walang problema sa luma ko, parang electrical sound ang tunog pero ginamit ko pa ng mga ilang taon sa luma ko ng alang problema. tapos eto na ang isang palaisipan sa isip ko mga 2 weeks ko ginamit tong psu nato sa bago ko na build then nag lalaro ako ng AC odyssey ng bigla nalang namatay ung monitor ko, ni restart ko ung pc dahil wala ng display pero gumagana ung mouse at keyboard ko ala lang display, tapos pag ka restart ko tiningnan ko sa event viewer ung error naka lagay display, after nun ni run ko unigine heaven para I testing nagulat ako sa at kumalahati nalang fps ng unigine dahil kabisado ko ang fps ko dun na dapat 42 naging 23 fps nalang sinubukan ko ayusin ung card nag reformat nako nag reinstall ng driver roll back at sinubukan ko iba ibang driver ayaw parin, gumamit na din ako ng ddu at umabot nako sa punto na nag reflashbios na 2 beses pa ni reflash iba ibang bios ang sinubukan ko pero same scenario parin, mabagal parin ung card tinesting ko sa luma ko na pc at ibang psu ganun parin tapos dinala ko ung card sa service center ng asus dito malapit samin at sabi nila malamang hardware na daw sa power delivery or mosfet daw tama stage 2 na daw ang sira nasa 3000-3500 ang paayos pambihirang buhay kako to kala ko ma eenjoy ko ung bago ko na build sumakit pa Lalo ulo ko sa kakaisip sobrang stress nako sa kakaisip talaga kung ano gagawin sa palagay nyo ka tipidpc worth pa kaya ipaayos to ng 3-3.5k or bumili nalang ako ng bago? gtx 970 strix po pala ung card mag 4 years na sa march 15 sana at naka overclock po siya ng nagkaganyan 120 sa core clock 400 sa memory wala ako ginalaw na voltage at eto pa sa gpu-z minsan Nakita ko na x4 ang bus width ng card na dapat x16 nilagyan ko po kasi ng konting support ung gpu para hindi mag sag tukod lang na prang leggo pag inaalis ko ung support nagiging x16 ng inugauga ko ung card nagging x1 langya kako Lalo sumakit ulo ko tapos ni reseat ko ung card Ayun umayos bumalik na sa x16 dumagdag pa sa iniisip ko yang problema na yan kaya sumasakit Lalo isip ko kahit sa luma ko nagiging x4 x8 po yan minsan ano kaya my problema niyan kahit sa bago nag x4 eh?, sapalagay nyo psu kaya my problema na pumatay sa card na ok naman ng ilang taon sa luma ko or talagang bumigay na ung card inabutan sa bago ko na build natatakot na tuloy ako gamitin ung psu sa bago ko at Lalo bago mga parts ko, sa ngayon po nakatangal ung gpu sa bago at onboard ang gamit ko,balak ko din bumili ng bagong gpu this march at iniisip ko kung bumili na din ako ng bago na psu for peace of mind lang ano sa palagay nyo ka tpc gamitin ko parin etong x 750 ko or bumili nako ng bago? pasensha na po sa haba ng message ko at watak watak na tanong hehe at kulang pa po yan sa dami ng mga itatanong ko talaga eto po ung tunog na galing sa psu https://www.youtube.com/watch?v=ex-s1ecGiLs safe pa po kaya gamitin tong psu sa bago kahit alang gpu?gamit ko pa ngayon ung x750 thanks po
-- edited by calmaardee on Feb 15 2019, 10:07 AM
-
CrkDice
on
15 Feb 19 @ 10:57 AM #
^its not normal per se, but not defective, its just a coil whining, or vibration ng induction coil , general cause is loose yung loops ng induction wires sa loob, stick glue can temporarily fix it.
i think your gpu is dying but it only needs reheating, you can do the oven trick method, usually sa tagal mo ng ginagamit, nagkakarun sila ng cold solder yung main chip whichi is nag loloose contact na yung ibang connectors beneath, masiadong mahal yung 3500, if malapit ka sa mrt shaw, sa 2nd floor northbound budgetsandgadgets look for william, 400 lang singil, advance yung pang reheat na machine nya dun if you dont want to risk the oven method
may mga kamalasan din talaga tayong naeexperience and sa kasamaang palad, nag cocoincide kung kelan me bago tayong partz, like me i was excited to install my new 500 gig ssd, then pagkasaksak ko ngspark socket kasi medyo maluwag then gpu dead on the spot,
-- edited by CrkDice on Feb 15 2019, 11:01 AM
-
calmaardee
on
15 Feb 19 @ 02:35 PM #
@CrkDice ganun ba sir sige sir Salamat sa opinion nakakapanghinayang lang talaga gusto ko kasi maayos para sa isang pc ko ,ung dad ko kasi gumagawa ng mga 2a radio my baka sakali ma ayos nya maipa check muna sakanya at my mga alam sya sa mga ganyang bagay. btw sir thanks sa reply
-
awakeruze
on
15 Feb 19 @ 03:40 PM #
^
Question: may HP G42 laptop (AMD CPU) yung pinsan ko, na-reheat na dati kaso bumalik yung problema after a year or so. Worth it pa bang ipa-reheat ulit o huwag na lang dahil malamang bumalik lang ang problema?
-
polka
on
16 Feb 19 @ 07:54 AM #
@calamardee
go here, we already talk about that
<click here for link>
in short, you might as well deal with the coil whine, its normal, electronics 101, if you hate it that much, then buy a specialized hardware like a series of "be quiet" components or go take a electonics engineering course and invent a replacement for inductors that eliminates noise.
-
bitfrost
on
16 Feb 19 @ 08:05 PM #
Pa tulong po. Installed 12gb Ram 3.93 GB Ram Usable.
Nilinis ko lang PC kanina medyo madami na kasi alikabok gamit mini blower na pang PC naman. After mag linis napansin ko na medyo nag stutter ako habang nag lalaro. Pag check ko ng RAM usage, napansin ko na yung 4gb na stick lang yung nagagaamit at na detect naman yung isang stick ko ng 8gb pero hindi usable.
Same din sa Bios na parehas na dedetect yung stick pero 4gb lang readable. Magkaiba pala yung model ng RAM ko pero same brand, nag work naman sya before ngayon lang ulit nag loko.
Naging issue na sakin to last year pero hindi ko maalala kung pano ko sya na resolve.
<click here for link>
<click here for link>
<click here for link>
-
joeryan
on
19 Feb 19 @ 01:34 PM #
mga boss anu kaya ang compatible na video card sa EMaxx A58FM2HD-iCAFE ...may existing memory card ang board ko na 4gb ddr3...need your expert advise..
-
aishshit23
on
20 Feb 19 @ 11:38 AM #
Mga sir, may tanong lang po ako about sa dell optiplex 780 dt. Nabili po sya ng friend ko last week then tinry po namin sya lagyan ng gpu (geforce 9400gt). Then tinry namin iboot tapos ayaw nya magtuloy sa windows. After that, tinanggal na po namin ung gpu tried to boot ulit pero ayaw na nya magboot. Ano oo kayang problema ntio?
-
comp071
on
23 Feb 19 @ 12:01 PM #
^ try mo linisin yung ram slots at ram contacts
-
comp071
on
23 Feb 19 @ 12:02 PM #
@joeryan
kahit ano naman pwede depende na lang sa processor mo para mag "bottleneck"
-
comp071
on
23 Feb 19 @ 12:03 PM #
@bitfrost
try mo kaya yung 8gb lang ang naka lagay
-
usernamer2
on
27 Feb 19 @ 02:40 AM #
Meron po ba ditong may experience sa gigabyte radeon rx 570 blinking led? Psu ko seasonic 520. Both bnew. Tia
-
tpcjml
on
04 Mar 19 @ 08:55 AM #
pede bang plug n play yung windows os? dami kong nakikitang nag titinda ng hdd with pre installed os na gagana ba yun magkaibang hardware?
-
t3nma
on
04 Mar 19 @ 10:49 AM #
^Nope, yun OS kase may drivers for hardware na detected niya upon installation. Kaya nga pag nagpalit ka ng mobo bigla error na si windows.
-
awakeruze
on
04 Mar 19 @ 10:53 AM #
@tpcjml
If it's an OEM install (laptop/desktop came preinstalled with Win 10), then the answer is no, same with OEM installs of Win 7 and 8/8.1, then upgraded to Win 10 during the now-ended free Win 10 upgrade period.
-
polka
on
04 Mar 19 @ 08:42 PM #
medyo outdated na kayo ah, with newer os today like Windows 10, pwede mo na gamitin yung HDD sa ibang computer to your new computer, kailangan mo lang install yung drivers like videocard and stuff. this is very useful for major computer upgrades.
hindi na ito katulad dati ng 7 or 8 or xp, though you can make those thing work by just using the windows installation disk and enter maintenance mode to reinstall the SATA/AHCI drivers.
of course, after the migration, you have to deal with licensing. of course for windows 10, this is not a issue lalo na kung retail key yung ginamit nyo (not OEM) that is paired with your MSCDN account as your default windows login (if you bought your windows licensce online paired with your microsoft account, or bought it on Windows Store, auto activate na yan as soon as login).
-- edited by polka on Mar 04 2019, 08:47 PM
-
t3nma
on
04 Mar 19 @ 09:25 PM #
^Yes, but the question was very generic. Technically it can be used but we can't verify if it will be a valid licensed product. So I opted to say na di pwede.
-
awakeruze
on
04 Mar 19 @ 11:31 PM #
@t3nma
There's a high chance that It won't be validated as genuine, especially OEM preinstalled ones.
Laptops that come with Windows 10 preinstalled have the license and product key embedded in the BIOS. If its HDD is installed in a different machine, Windows will detect that the license and product key are missing.
- Post deleted #12206290
-
tpcjml
on
11 Mar 19 @ 07:14 PM #
is this safe o need to upgrade cpu cooler?
