@breezybish
try unplugging the PSU cable then hold down the power button for 30 seconds. remove side panel and do a clear RTC/CMOS.
Forum Topic
PC Technician Lounge (Trading/Selling Not Allowed)
-
Share ko lang, baka may same experience:
Recently, biglang nag fa-5 short beeps ang pc tuwing unang boot. Tapos black screen lang. Then pindot reset button tapos matagal bago tumunog yung one beep na good boot. Tagal din magboot to windows. After some research, cpu error daw. Pwede rin daw RAM.
After further analysis, before ako magkalas, inisip ko rare ang cpu error. Ang pinakalumang part ng computer ko ay cmos battery. So pinalitan ko ng bago. Ayun nawala ang 5 beeps and mabilis na magboot. -
Share ko exp kahapon
Naglinis ako ng cpu heatsink pagbalik ko nagreboot every 20s, no signal. Unang ginawa ko linis ng alcohol(90%)memory module, tinanggal ko sa case baka grounded. Try ko ibang psu, remove cmos batt, same reboot pa rin. Frustrated na ako plan ko pa naman ibigay sa pamangkin ko. Last sinubukan ko slot 2 lang ayon gumana. I notice pag top down cooler ang dami dust sa side. -
Gud day po mga sir.nagpalit po ako ng case na Mi-A2 Gstorm. Ayaw na pi tumuloy mag on nag off kaagad.ano po kaya problema
-
^
Remove the motherboard from the casing then test. -
Hi mga sir, may question ako about sa RX 580 ko po, Bale sa games lang sya may artifacts na nagflaflash na lines parang nag gliglitch na lines pag sa laro lang pero pag browsing or nuod movie wala namang ganyan. and pag naglalaro ng heavy games like rainbow six seige, mag cracrash ung AMD software pati ung laro. marerepair po kaya to?
yung huling nangyari is, habang naglalaro ako ng rainbow six, nag freeze ung pc and nag black screen ung monitor ng about 1minute then naka recover naman pati ung AMD software then ayun na nga nagkaroon na ng mga glitch lines pag sa laro lang. Thank you po -
Agad bang may artifacts pag nag games ka?
Check mo temp ng GPU sa Adrenaline, ung radeon software, kung ano temps mo. Pag idle dapat nasa 30s to 40s. Sa games, nag-vary pero usually nasa 60s. Masyado mainit na pag nasa around 80 ka. -
@bum4now
pag sa mga menu or loading screen, wala syang artifacts. pag sa in game na sya nagkaka artifacts ung glitch lines.
Idle temp around 40-50
in game ( League of legends) - around 60
in game(heavily titled games) rainbow six/ farcry 5 - 60-70temps then mag crash ung AMD software pag nag start na ung game after loading screen.
tried reinstall/downgrade driver.
tried repaste thermal
tried undervolt/underclock
yung naiisip ko baka sa vram na nya ung sira since pag nag high settings ako sa mga games mag crash lalo na pag rainbow six pero pag low settings ok naman sya pero may glitch lines, or any idea kailangan na ba ipa reball ito? -
I'd say last alternative ung physical repair ng card.
Try mo leave open ung case, tutok mo electric fan then run the games. This will tell you kung issue with temps.
Double check if gpu fan is working.
Tried repaste thermal, do you mean pinalitan mo ung thermal paste? Ano klase paste ginamit mo? Also, pinalitan mo ba ung conductive tape ng vram (kung meron)? -
@bum4now
yes pinalitan ko ng thermal paste yung arctic and sa pads naman yung gigaware brand from shopee but no sucess still ganun pa din sya.
Pinunta ko na sya sa tech and sabi nya idadaan na daw nya sa gpu reball. Hopefully sana maayos since ang hirap pa naman makahanap ng decent price ng rx 580 ngayon. Thank you sa mga suggestion and help mo -
Saan nag papawarranty ng gskill ripjaws v 2x4 8gb 3200mhz locally? Yung shop na pinagbilan ko close na yata kasi eh. 2016 ko nabili and may mga errors sa memtest.
-
Mga sir, hingi po ng opinion nyo, yung pc ko is having a hard time na mag boot may times na pag press ng power button (no light sa keyboard, mouse and no display detected) but all the rgb and fans, cpu fan, gpu fans are working. would need to keep restarting the pc several times bago sya mag boot ng normal. im thinking na failing PSU ang problem, would just like to inquire baka may iba pa kyo alternative na naiisip na cause. my PSU pala is sufficient wattage supposedly for my rig.
-
^pwede din motherboard or proc. Pero last time that happened to me it was the proc.
-
@RuZuCoE
Try stripping down to just the PSU, mobo and ram (1 stick only if you have multiple and try the other separately if the problem re-occurs) 1st. This will help narrow down if there might be a component causing the issue.
If the problem goes away, start re-adding 1 component at a time to determine the faulty part.
If the problem persists, the best way to avoid guessing to borrow a psu if you don't have a spare.
If problem goes away with a spare psu, good chance it most likely could be the psu.
If problem persists with the spare psu, then it could be the mobo. -
Hi guys, just an update, removed my GPU riser and so far mukang ok na sya. any idea bakit ganun pag naka riser?
-
RuZuCoE Send Message View User Items on 07 Jun 21 @ 08:18 PM #
Hi guys, just an update, removed my GPU riser and so far mukang ok na sya. any idea bakit ganun pag naka riser?
most likely faulty/incompatible riser cables.
-
ano po ba possible reasons kapag "no boot, no POST, no beep, no display". umaandar po fans(cpu, case). since 2010 pa po, tried also replacing the 2032 battery(cmos) , test it using a new PSU...wala pa rin.
-
@sethmartin
Sounds like no post since umaandar ung fan. Since you mentioned no beep, did you try running the mobo without ram?
Since you have a spare PSU, remove all components including ram and turn on. If no beep, it could be a problem with the mobo. Check mo ung manual mo, kung may LED diagnostics ung board, that can help you determine the cause.
Since 2010 pa, possible na baka may mga bloated capacitors ung board. Try a visual inspection.
Kung parang talagang mobo ung problem and parang for replacement na, you can still try washing with joy liquid soap as a last resort. -
Mga lodi,
pag may cyclic redunduncy error ang hdd wala nang pagasa na maformat uli? nakaka ilang bili na ako ng hdd na readable naman nung nasa seller pa. may video kasi na 100 health. pag dating sa akin ay cyclic redunduncy error. nadedeteck naman sa disk management pero ayaw mag format. -
@griid
That's usually caused by one or more bad sectors.
When I encounter this issue in an HDD, and the drive doesn't contain any data, I do one of two things:
1. low-level format (AKA zero fill) -- this writes binary zeros on the entire disk. any bad sector is marked by the drive's firmware and replaced by a spare sector--HDDs have a certain amount of sectors set aside as spares and used as replacements for defective ones. The act of replacing a bad sector with a spare one is called bad sector remapping, or just remapping for short.
2. defect scan with bad sector remapping. it reads the entire disk, and any read error detected is marked as a bad sector and remapped. It may be faster, but might not catch all errors.
There are a number of HDD diagnostic programs (usually supplied by HDD vendors like Western Digital and Seagate) that can do these.
Do note that either procedure will take a long time--at least 1 hour; the bigger the drive, the longer it will take. After it completes, let the hard drive idle for at least 15 minutes to cool down before turning off the computer.
Also, if you've done either of these and new bad sectors pop up later, it's a sign that the HDD has a major issue (usually a damaged read/write head that scratches the disk surface. You should back up files immediately. -
@awakeruze
salamat pre sa tip pero papaano mo ma 0-fill yung hdd kung ayaw nyang maging active partition? nakikita pero hindi ma initialize at hindi maformat yung partition? -
Medyo mahirap mag sugal sa lumang hdd. Understandable kung nagtitipid pero sakit ng ulo pag nagka data loss or if you're relying on it for work.
If you want a different way of getting the hdd to maybe work, partition mo cya into 2 or 3. Then try formatting the partitions. This kind of a shortcut but would obviously cause you too have unusable space in your hdd since it's hit out miss but manila mo lang cya magagwa. The one(s) that work could be usable. But of course, ung tinuro ni awakeruze is the the correct method.
On the other hand, baka pwede mo pa soli. Wala bang personal guarantee?
-- edited by bum4now on Jun 12 2021, 05:13 PM -
@griid
You don't need to partition it when zero-filling a drive. You're basically wiping the entire disk after all. -
@bum4now:
salamat po. try ko po. -
Hello mga masters! :)
Ano po kaya prob ng laptop ko? Laging nawawala yung wifi connection. Ang error ay hindi daw makita yung wifi network.
Ang ginagawa ko ngayon, "Troubleshoot." Minsan gumagana, minsan need reset WiFi or Network Adapter. Other times, uninstall-install ng driver. Pati yung Bluetooth nawawala din. Nangyare to pagkatapos nung isang Windows Update sometime Feb-March 2021.
Ano po kaya remedyo bukod sa reformat ng buong laptop? TIA -
Bluetooth and wifi are often on the same card on laptops.
Possibilities:
- check the update last feb- mar; sometimes driver updates come in through windows updates. You can try uninstalling it if there was one one related to your problem
- check the driver date for your wifi device. If it was updated, the date will be reflected. You can do a rollback if this was the case
- system restore, this can work but going back 3-4 months isn't always a good thing
- try sfc /scannow from elevated command prompt. Can fix corrupted system files. Doesn't always work pero rarely causes problems so worth doing
- option which will cost some money but can solve your problem, get a usb wifi/Bluetooth dongle. It's not terribly expensive and you shouldn't need to reinstall windows. Added benefit, kung medyo luma laptop mo, you may have wifi4 or older, you can get wifi 5 pretty cheap, not sure about wifi6 -
hello peeps,
i have a hyperX fury 8GB/2133/4DDR black, what a good procie and mb to overclock?
new to oc hehe -
Ask ko lang. Bakit biglang nakuryente ako pagtouch ko sa may likod na part ng PC ko.? Ngayon lang ito ng nangyari, dati kc wala naman. Nakasaksak naman ng maayos mga cable sa likod..Check ko pagkasaksak ng PC ko sa Secure AVR, ok nman. Ang PSU ko is Corsair 80+. Ano kaya dahilan?
-
^ walang grounding system yung saksakan nyo.
the only economical solution for this is wear a dry rubber slippers para hindi ka makuryente. or do a electrical system overhaul in your house at sabihin mo sa electrician na lagyan ng grounding yung bahay nyo. papalitan nila lahat yung saksakan ng 3 yung paa, and also will add some sort of thing copper rod (or cheap iron rod) at nakabaon yan sa labas ng bahay nyo and thats all connected to grounding sa bahay nyo.
-- edited by polka on Jun 27 2021, 09:18 AM -
^Meron naman. Yan un 3rd hole noh? May 3 holes ang wall outlet, ang avr, 3 holes rin. Actually, rewired na electrical system namin. 3 holes mostly ang saksakan sa mga appliances, ang hindi lang 3 holes, ay ang convenience outlet, saksakan ng mga celfone chargers namin. Ang hindi ko lang sure ay ang "copper rod (or cheap iron rod) at nakabaon yan sa labas ng bahay nyo" ..yan, check ko pa yan..